Articles | Volume 18, issue 8
https://doi.org/10.5194/acp-18-5765-2018
https://doi.org/10.5194/acp-18-5765-2018
Research article
 | 
25 Apr 2018
Research article |  | 25 Apr 2018

The influence of model spatial resolution on simulated ozone and fine particulate matter for Europe: implications for health impact assessments

Sara Fenech, Ruth M. Doherty, Clare Heaviside, Sotiris Vardoulakis, Helen L. Macintyre, and Fiona M. O'Connor
Abstract

We examine the impact of model horizontal resolution on simulated concentrations of surface ozone (O3) and particulate matter less than 2.5 µm in diameter (PM2.5), and the associated health impacts over Europe, using the HadGEM3–UKCA chemistry–climate model to simulate pollutant concentrations at a coarse ( 140 km) and a finer ( 50 km) resolution. The attributable fraction (AF) of total mortality due to long-term exposure to warm season daily maximum 8 h running mean (MDA8) O3 and annual-average PM2.5 concentrations is then calculated for each European country using pollutant concentrations simulated at each resolution. Our results highlight a seasonal variation in simulated O3 and PM2.5 differences between the two model resolutions in Europe. Compared to the finer resolution results, simulated European O3 concentrations at the coarse resolution are higher on average in winter and spring ( 10 and  6 %, respectively). In contrast, simulated O3 concentrations at the coarse resolution are lower in summer and autumn (1 and 4 %, respectively). These differences may be partly explained by differences in nitrogen dioxide (NO2) concentrations simulated at the two resolutions. Compared to O3, we find the opposite seasonality in simulated PM2.5 differences between the two resolutions. In winter and spring, simulated PM2.5 concentrations are lower at the coarse compared to the finer resolution (8 and 6 %, respectively) but higher in summer and autumn ( 29 and  8 %, respectively). Simulated PM2.5 values are also mostly related to differences in convective rainfall between the two resolutions for all seasons. These differences between the two resolutions exhibit clear spatial patterns for both pollutants that vary by season, and exert a strong influence on country to country variations in estimated AF for the two resolutions. Warm season MDA8 O3 levels are higher in most of southern Europe, but lower in areas of northern and eastern Europe when simulated at the coarse resolution compared to the finer resolution. Annual-average PM2.5 concentrations are higher across most of northern and eastern Europe but lower over parts of southwest Europe at the coarse compared to the finer resolution. Across Europe, differences in the AF associated with long-term exposure to population-weighted MDA8 O3 range between 0.9 and +2.6 % (largest positive differences in southern Europe), while differences in the AF associated with long-term exposure to population-weighted annual mean PM2.5 range from 4.7 to +2.8 % (largest positive differences in eastern Europe) of the total mortality. Therefore this study, with its unique focus on Europe, demonstrates that health impact assessments calculated using modelled pollutant concentrations, are sensitive to a change in model resolution by up to ±5 % of the total mortality across Europe.

Dates
1 Introduction

A substantial number of epidemiological studies have derived risk estimates for mortality associated with long-term exposure to ambient fine particulate matter with an aerodynamic diameter of less than 2.5 µm (PM2.5) (Krewski, 2009; Brook et al., 2010; WHO, 2013) and also recently, to a lesser extent, for long-term exposure to ozone (O3) (Jerrett et al., 2009; Forouzanfar et al., 2016; Turner et al., 2015). Differences in risk estimates produced from different epidemiological studies can be due to differences in methodologies, air pollution and health data used, including the size and spatial extent of cohort populations. For O3, these long-term risk estimates are derived from North American studies. In this region O3 data is typically monitored only during the O3 season (April–September), hence these derived O3-risk estimates apply only to ozone occurring in the warm seasons.

Air pollutant exposure estimated from concentrations measured at fixed monitoring stations, is often used to estimate health impacts at the cohort-scale (Cohen et al., 2004). However, quantifying the adverse health effects of air pollution at the continental-scale requires atmospheric models (with resolutions ranging from  250 to 50 km) to simulate pollutant spatio-temporal distributions across these scales (e.g. West et al., 2009; Anenberg et al., 2010; Fang et al., 2013; Silva et al., 2013; Lelieveld et al., 2015; Malley et al., 2017). Amongst a number of factors, simulated air pollutant concentrations may vary depending on the three-dimensional chemistry model used, its set-up and the model resolution (e.g. Markakis et al., 2015; Schaap et al., 2015; Yu et al., 2016; Neal et al., 2017). Although the same model processes are represented at different model resolutions, simulated pollutant concentrations can vary due to differences in (i) the resolution of emissions, which may have a nonlinear effect on the chemical formation of pollutants, and (ii) the resolution of the driving meteorology (Valari and Menut, 2008; Tie et al., 2010; Arunachalam et al., 2011; Colette et al., 2013; Markakis et al., 2015; Schaap et al., 2015).

The impact of model horizontal resolution on simulated O3 concentrations has been primarily linked to less dilution of emissions when using a finer resolution (Valari and Menut, 2008; Tie et al., 2010; Colette et al., 2013; Stock et al., 2014; Schaap et al., 2015). Investigating the impact of increasing model horizontal resolution from 48 to 6 km on O3 concentrations in Paris, Valari and Menut (2008) found modelled surface O3 to be more sensitive to the resolution of input emissions than to meteorology. A number of other studies note the sensitivity of simulated O3 to simulated nitrogen oxide (NOx) concentrations that determine the extent of titration of O3 by nitrogen monoxide (NO) (Stock et al., 2014; Markakis et al., 2015; Schaap et al., 2015). Furthermore, Stock et al. (2014) found the impact of spatial resolution (150 km vs. 40 km) on simulated O3 concentrations to vary with season across Europe. In winter, higher NOx concentrations produced more pronounced titration effects on O3 at 40 km resolution with a mean bias error (MBE) of 3.2 %, leading to lower O3 concentrations than at 150 km resolution (MBE = 14.4 %). In summer, although similar results were found for O3 concentrations simulated at the coarse (MBE = 29.7 %) and fine resolution (MBE = 32.8 %) simulated boundary layer height was suggested to be largely responsible for the spatial differences in O3 concentrations at the two resolutions.

PM2.5 concentrations have also been found to be sensitive to the model horizontal resolution (Arunachalam et al., 2011; Punger and West, 2013; Markakis et al., 2015; Neal et al., 2017). In the US, Punger and West (2013) found population-weighted annual mean PM2.5 concentrations to be 6 % higher at 36 km compared to 12 km, but 27 % lower when simulated at 408 km compared to 12 km. However in this study, statistical averaging was used to estimate pollutant concentrations at the coarsest resolutions, and therefore differences in emissions and meteorology and their atmospheric processing between the resolutions were not included. In contrast, Li et al. (2015) found annual mean PM2.5 concentrations simulated at a resolution of  2.5 in the US to be similar to PM2.5 concentrations simulated at a resolution of  0.5 suggesting that the horizontal scales being compared and the methodology for comparison are important. However maximum PM2.5 concentrations which occur in highly populated regions were found to be 21 % lower at the coarse resolution (Li et al., 2015).

As outlined above, a number of studies have analysed the effect of model resolution on O3 and PM2.5 concentrations but few have looked at the sensitivity of the associated health impacts to model resolution (Punger and West, 2013; Thompson et al., 2014; Li et al., 2015). Punger and West (2013) found mortality associated with long-term exposure to O3 in the US to be 12 % higher at a 36 km resolution compared to the mortality estimate at 12 km, as a result of higher O3 simulated at the coarser-scale. Thompson et al. (2014) also found that especially in urban areas, the human health impacts associated with differences in O3 between 2005 and 2014 calculated using a coarse resolution model (36 km) were on average two times greater than those estimated using finer scale resolutions (12 and 4 km). In addition, Thompson and Selin (2012) found that the estimates of O3-related mortalities between a 2006 base case and a 2018 control policy scenario at a 36 km resolution were higher compared to estimates at the finer resolutions (12, 4 and 2 km). However, their health estimates at the 36 km resolution fall within the range of values obtained using concentrations simulated at the finer resolutions used.

For PM2.5-related health estimates, studies by Punger and West (2013) and Li et al. (2015) both found that attributable mortality associated with long-term exposure to PM2.5 in the US was lower for their coarser resolution simulations (> 100 km) due to lower simulated PM2.5 concentrations in densely populated regions. However, Thompson et al. (2014) found that using model horizontal resolutions of 36, 12 and 4 km had a negligible effect on changes in PM2.5 concentrations and associated health impacts. This is likely due to the relatively small range of resolutions used by Thompson et al. (2014) compared to these other studies.

The majority of health effect studies relating to the impact of model resolution have been conducted in North America. Hence, similar studies are lacking over Europe. This study is therefore the first to examine the impact of two different model resolutions: a coarse ( 140 km) and a finer resolution ( 50 km) on O3 and PM2.5 concentrations, and their subsequent impacts on European-scale human health through long-term exposure to O3 and PM2.5. We define the sensitivity of health impacts to model resolution by calculating the attributable fraction (AF) of total mortality which is associated with long-term exposure to O3 and PM2.5 for various European countries, based on simulated concentrations at both resolutions, and expressed as a percentage.

The remainder of the paper is organised as follows. Section 2 describes the modelling framework used for both the coarse and finer simulations and the methods used to calculate the AF of mortality associated with O3 and PM2.5 for various European countries. Section 3 presents differences in seasonal mean O3 and PM2.5 concentrations between the two resolutions. In Sect. 4, we first analyse differences in warm season daily maximum 8 h running mean (MDA8) O3 concentrations and annual PM2.5 concentrations between the two resolutions, then quantify differences in country-level population-weighted MDA8 O3 and annual mean PM2.5 concentrations. Secondly, the country-level AF associated with long-term exposure to MDA8 O3 and annual mean PM2.5 simulated at both resolutions are presented. The conclusions of this study are then presented in Sect. 5.

2 Methods

2.1 Model description and experimental setup

The two chemistry–climate configurations used in this study are based on the Global Atmosphere 3.0 (GA3.0)/Global Land (GL3.0) configuration of the Hadley Centre Global Environmental Model version 3 (HadGEM3, Walters et al., 2011), of the Met Office's Unified Model (MetUM, Brown et al., 2012). The coarse configuration has a horizontal resolution of 1.875× 1.25 ( 140 km, Walters et al., 2011) while the finer configuration has a horizontal resolution of 0.44× 0.44 ( 50 km, Moufouma-Okia and Jones, 2014) with a domain covering most of Europe.

As this study focuses on health impacts, our analysis is restricted to European land regions. In both configurations, a 63 level hybrid height vertical co-ordinate system is used with 50 levels below 18 km and a surface level at 40 m. Gas phase chemistry is simulated within HadGEM3 by a tropospheric configuration of the United Kingdom Chemistry and Aerosol (UKCA) model (Morgenstern et al., 2009; O'Connor et al., 2014). The chemistry scheme used for both configurations is the UKCA Extended Tropospheric Chemistry (UKCA-ExtTC) scheme (Folberth et al., 2018) which is an extension to the TropIsop standard chemistry scheme (O'Connor et al., 2014) and includes 89 chemical species. Boundary layer mixing for both configurations is based on Lock et al. (2000) and includes an explicit entrainment parameterisation and non-local mixing in unstable layers. The GA3.0/GL3.0 configuration of HadGEM3 (Walters et al., 2011) also includes an interactive aerosol scheme called CLASSIC (Coupled Large-scale Aerosol Simulator for Studies in Climate; Jones et al., 2001; Bellouin et al., 2011) from which PM2.5 concentrations are estimated. CLASSIC simulates ammonium sulphate and nitrate, fossil-fuel organic carbon (FFOC), mineral dust, soot and biomass burning (BB) aerosol interactively. Biogenic secondary organic aerosols are prescribed from a climatology. Sea salt aerosol is diagnosed over ocean only and does not contribute to particulate matter over land.

The model simulations for both these configurations cover a period of one year and nine months starting from April 2006, from which the first nine months were discarded as spin-up. The coarse configuration uses monthly mean distributions of sea surface temperature (SST) and sea ice cover (SIC), derived for the present-day (1995–2005) from transient coupled atmosphere–ocean simulations (Jones et al., 2001) of the HadGEM2-ES model (Collins et al., 2011). Using a simple linear re-gridding algorithm, the SST and SIC climatologies developed for the coarse configuration were downscaled to the finer configuration. The coarse configuration was set to produce lateral boundary conditions (LBCs) at six-hourly intervals which were then used to drive the finer configuration.

A consistent set of baseline emissions have been used for both configurations by using the same source data and then re-gridding to the coarse and finer resolutions of the chemistry–climate model. The surface emissions for chemical species were implemented from emission data at 0.5 by 0.5 resolution developed by Lamarque et al. (2010) for the Fifth Coupled Model Inter-comparison Project (CMIP5) report which include reactive gases and aerosols from anthropogenic and biomass burning sources. Both model configurations are driven by decadal mean present-day emissions from Lamarque et al. (2010), representative of the decade centred on 2000. Biogenic emission of isoprene and monoterpenes are calculated interactively following Pacifico et al. (2011) and the biogenic emissions of methanol and acetone are prescribed, taken from Guenther et al. (1995). A full description of other biogenic emissions and the coarse and finer configurations can be found in Neal et al. (2017).

The two configurations are consistent in terms of driving meteorology and emissions as discussed above, however a change in model resolution also requires changes to the model's dynamical time step (from 20 min – coarse resolution to 12 min – finer resolution) as well as some of the parameters in the model parameterisations schemes that are resolution dependent. In this study we assume any such differences to be a model resolution effect. To compare pollutant concentrations simulated at the two resolutions, the coarse model results were re-gridded to the finer resolution via bi-linear interpolation and differences between the two configurations were then calculated at each grid box. For consistency, all figures, tables and values shown in the following sections show differences calculated as coarse minus finer results. All pollutant concentrations used in this study have been extracted at the lowest model level with a mid-point at 20 m. While this level is considered representative of surface or ground-level concentrations, local orographically driven flows or sharp gradients in mixing depths cannot be represented at this vertical resolution (Fiore et al., 2009).

2.2 Measurement data

Modelled seasonal mean O3 and PM2.5 concentrations for 2007 were evaluated using measurement data from the European Monitoring Evaluation Programme (EMEP) network (http://ebas.nilu.no, last access: 19 April 2018). We note that all EMEP stations are classified based on a specific distance away from emission sources so as to be representative of larger areas. For example the minimum distance from large pollution sources such as towns and power plant is  50 km (Tørseth et al., 2012; EMEP/CCC, 2001). We chose a sub-set of the available EMEP O3 measurement sites with an altitude less than or equal to 200 m above sea level to focus on near-surface comparisons between measurements and simulated O3 concentrations (52 sites – Fig. 1). As there are fewer measurements of PM2.5 for 2007, all available EMEP measurement sites were used for PM2.5 evaluation (25 sites – Fig. 1). All modelled O3 and PM2.5 concentrations shown in this study were taken from the lowest vertical model level which reaches a height of 40 m. To perform an observation–model comparison, simulated pollutant concentrations were extracted at measurement site locations using bi-linear interpolation.

2.3 Health calculations

Annual total mortality estimates associated with long-term exposure to O3 and PM2.5 are frequently calculated by estimating the country-level attributable fraction (AF) of mortality, based on concentration–response relationships associated with each pollutant, and then multiplying the AF by the baseline mortality rate. Since we are interested in the effects of changing resolution on pollutant concentration, in our analysis, we focus on the absolute values and differences in the AF between the two resolutions, rather than calculating mortality associated with each pollutant, which also depends on underlying baseline mortality rates. This allows us to isolate the effect of model resolution on health impacts. We note that differences in AF will be the same as the differences in mortality between the two resolutions (expressed as a percentage of total mortality), if calculated as described in this section.

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f01

Figure 1EMEP measurement stations with altitude less than or equal to 200 m, used for seasonal mean surface O3 comparison to modelled concentrations (52 sites are red) and EMEP measurement stations used for seasonal mean PM2.5 comparison to modelled concentrations (25 sites are blue).

Download

Although there is limited evidence available for the long-term health impacts of O3 especially in Europe (The UK Committee on the Medical Effects of Air Pollution, COMEAP, 2015), a number of studies have quantified the adverse health impacts associated with long-term exposure to O3. In this study we apply the Health Risks of Air Pollution in Europe (HRAPIE) project recommended coefficient for long-term exposure to O3 (WHO, 2013) to investigate the sensitivity of health calculations to the model resolution used to simulate O3 concentrations. This concentration–response coefficient is derived from the single-pollutant analysis of the American Cancer Society Cancer Prevention Study II (CPS II) cohort study data in 96 metropolitan areas of the US (Jerrett et al., 2009) which has been used by previous studies (e.g. Anenberg et al., 2009; Punger and West, 2013; Thompson et al., 2014; Cohen et al., 2017); but is re-scaled from 1 h mean to 8 h mean concentrations using the ratio 0.72, derived from the APHEA-2 project (Gryparis et al., 2004). The value recommended by HRAPIE for the concentration–response coefficient, or β value (Eq. 1), for the effects of long-term O3 exposure on respiratory mortality is 1.014 (95 % Confidence Interval (CI) = 1.005, 1.024) per 10 µg m−3 increase in MDA8 O3 during the warm season (April–September) with a threshold of 70 µg m−3 (WHO, 2013). For estimating the health impact of long-term exposure to PM2.5 on all-cause (excluding external) mortality, HRAPIE (WHO, 2013) recommends a relative risk coefficient of 1.062 (95 % CI = 1.040, 1.083) per 10 µg m−3 increase in annual average concentrations (with no threshold), which is based on a meta-analysis of cohort studies by Hoek et al. (2013).

For MDA8 O3, the risk estimates above, suggested by HRAPIE, are based on data from the American Cancer Society (ACS) cohort (Jerrett et al., 2009) during the warm season re-scaled from 1 to 8 h means (WHO, 2013). Since MDA8 O3 concentrations in the summer months exceed 70 µg m−3 for most areas included in the ACS study, little information exists on the shape of the concentration–response relationship at low levels. For this reason, following HRAPIE suggestions, only MDA8 O3 concentrations exceeding 70 µg m−3 and averaged between April and September were used in the present study to calculate O3-related health impacts. For PM2.5-related health impacts we use annual averages with no threshold. As the β values used for O3 and PM2.5 are from the ACS cohort, the estimates in this study exclude people younger than 30 years.

For each model resolution, simulated air pollutant concentrations were used to calculate the country-average AF of respiratory or all-cause mortality associated with long-term exposure to O3 and PM2.5, respectively. Specifically, the country-average AF is derived from the country-averaged population-weighted pollutant concentration (xcountry) and concentration–response coefficient (β) as shown in Eq. (1) (e.g. Anenberg et al., 2010; Gowers et al., 2014):

(1) AF country = 1 - e - β x country

The country-averaged population-weighted pollutant concentrations (xcountry) were derived using gridded population data at a resolution of 5 km (GWPv3), obtained from the Socioeconomic Data and Applications Centre (SEDAC, http://sedac.ciesin.columbia.edu/data/set/gpw-v3-population-count-future-estimates/data-download, last access: 19 April 2018), following Eq. (2):

(2) x country = i country p i × x i i country p i ,

here, xi represents the pollutant concentration within each model grid-cell i and pi represents the total population (aged 30+ years) summed within each model grid-cell. For population-weighted PM2.5 concentrations, the simulated PM2.5 concentration for each model grid-cell was multiplied by the number of people within the same model grid-cell. This product was then summed for all grid-cells within the country and divided by the total population of the respective country. A similar procedure was used for MDA8 O3 concentrations. However, for populated–weighted MDA8 O3 concentrations, 70 µg m−3 was first subtracted from the simulated MDA8 O3 concentration at each grid-cell before multiplying by the population (any resultant negative concentrations were set to zero).

Table 1Statistical results comparing seasonal mean O3 concentrations simulated at the coarse and finer resolutions to observations from 52 stations within the EMEP network in 2007. Statistical results for all model grid-cells of both resolutions are also shown. Percentage differences between the two model resolutions are calculated as (O3  coarse  resolution O3  finer  resolution) (O3  coarse  resolution).

Download Print Version | Download XLSX

3 The impact of model resolution on pollutant concentrations

3.1 The impact of model resolution on seasonal mean O3: comparison with observations

Modelled and observed means, standard deviations (SD), normalised mean bias (NMB) and percentage differences between the two resolutions for all four seasons at the 52 EMEP site locations are shown in Table 1. Similarly modelled means, SD and percentage differences between the two resolutions are also shown for all model cells within the European domain (discussed in Sect. 3.2). Compared to measurements, mean values simulated by the chemistry–climate model across the 52 station locations are lower in winter (DJF) and higher in summer (JJA) and autumn (SON) with NMB values up to 19,  27 and  19 %, respectively. In spring (MAM), simulated mean O3 concentrations at the finer resolution are closest to observations (NMB =4 %), whilst in the other three seasons the simulated values at the coarse resolution are in closer agreement with observations (NMB =8,  24 and  5 %, respectively).

For all seasons, the SD of seasonal mean O3 concentrations, simulated at the two resolutions are more similar to each other than to observations. However, the SD across all 52 sites, simulated at the coarse resolution is higher than that simulated at the finer resolution.

Modelled versus observed seasonal mean O3 concentrations for each of the 52 EMEP station locations are shown in Fig. 2, with arrow lengths indicating the change in concentrations when simulated at the coarse versus finer resolutions. For both resolutions, higher O3 concentrations are simulated during summer compared to observations as noted above (between 50 to 150 µg m−3, Fig. 2). In winter, simulated O3 concentrations are lower compared to measurements (< 30 µg m−3), and are most similar to observations in spring and autumn in accordance with lower NMB (Table 1).

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f02

Figure 2Seasonal mean modelled vs observed O3 for 52 sites across the EMEP network for the year 2007. The arrow tails mark O3 concentrations at the coarse resolution while the arrow heads represent the corresponding O3 concentrations at the finer resolution. The 1 : 1 line shows agreement between observed and simulated O3.

Download

The magnitude of the differences in simulated O3 concentrations between the two resolutions varies seasonally, with the smallest (coarse–finer) differences in summer (green arrows, Fig. 2; 3 %, Table 1) and the largest difference in spring, as noted above ( 16 %, Table 1). Similar differences in July mean O3 concentrations between a 150 and a 40 km resolution were also found by Stock et al. (2014). Over the majority of the stations, during winter and spring, O3 concentrations simulated at the finer resolution are lower than concentrations simulated at the coarse resolution (downward arrows, Fig. 2; positive difference, Table 1). In contrast during summer and autumn, O3 concentrations are higher when simulated at the finer resolution (upward arrows, Fig. 2; negative difference, Table 1). These results are analysed further at the seasonal level in Fig. S1 of the Supplement to this article (Sect. S1, Fig. S1).

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f03

Figure 3Seasonal mean O3 simulated at the finer resolution (a–d), differences in seasonal mean O3 between the coarse and finer resolutions (O3  coarse  resolution O3  finer  resolution) (e–h) and NO2 (NO2  coarse  resolution NO2 finer  resolution) (i–l). Blue regions in middle and bottom panels indicate that pollutant concentrations at the coarse resolution are lower (negative difference) while red regions indicate that concentrations are higher (positive difference) than those at the finer resolution.

Download

3.2 The impact of model resolution on seasonal mean O3: spatial differences

This section extends our investigation to examine the impact of model grid resolution on the spatial distribution of O3 over the whole of Europe. The seasonal variation in O3 concentrations simulated at the finer resolution across Europe shows the same features as at the 52 site locations (Sect. 3.1), with the highest values in spring and summer (> 50 and up to 120 µg m−3, Fig. 3b and c, respectively) and the lowest values in autumn and winter (< 55 µg m−3, Fig. 3a and d, respectively). In all seasons, except winter, there is a clear latitudinal gradient with higher O3 concentrations in southern compared to northern Europe. In winter (Fig. 3a), very low O3 concentrations are simulated across much of Europe ( 30 µg m−3).

For most of Europe, in winter and spring, mean O3 concentrations are generally higher when simulated at the coarse compared to the finer resolution (Fig. 3e and f; Table 1,  10 and  6 % respectively), in agreement with the findings for the sub-set of 52 locations. However parts of northern Scandinavia and the UK, and parts of south-eastern Europe have lower O3 concentrations simulated at the coarse resolution in these two seasons. In summer and autumn, O3 concentrations are slightly lower when simulated at the coarse compared to the finer resolution (1 and 4 % respectively, Table 1) as found for the sub-set of locations, except in areas of easternmost Europe (especially in autumn) and parts of Spain and Italy (Fig. 3g and h). The greatest positive differences in simulated O3 concentrations, i.e. higher values at the coarse resolution, are found in winter, especially in the far south of Europe in Spain ( 20 µg m−3, Fig. 3e). Some of these positive differences are clear around the coastal regions which is likely due to differences in the land/sea mask at the two resolutions, which leads to less deposition over oceanic grid-cells at the coarse resolution and higher simulated O3 concentrations compared to the same locations that are designated as land at the finer scale (Coleman et al., 2010). In addition, large positive differences in simulated O3 concentrations between the two resolutions occur over the Alps, whereby simulated O3 concentrations are higher at the finer scale (Fig. 3e and h). This is most likely due to the differences in orography at the two resolutions with higher elevations at the finer scale leading to higher O3 concentrations.

Differences in simulated seasonal mean NO2 concentrations at the two resolutions show similar, but less extensive differences and generally inverse patterns as for O3 concentrations, with some negative differences, i.e. lower NO2 values in winter and spring (Fig. 3i and j), when simulated at the coarse compared to the finer resolution. In contrast, in summer and autumn, NO2 concentrations are higher in some regions when simulated at the coarse compared to the finer resolution (e.g. Italy; Fig. 3k and l). An inverse relationship i.e. a positive difference in O3 concentrations and a negative difference in NO2 concentrations is most prominent for locations in Spain (all year around) and Italy (winter and spring) and parts of the Benelux region (southern UK and Netherlands; all year around). This inverse relationship is driven by lower NOx concentrations at the coarse resolution which lead to less O3 titration by NO compared to the finer resolution (Fig. 3i). This in turn results in higher simulated seasonal mean O3 concentrations at the coarse resolution compared to the finer resolution (Fig. 3e).

The planetary boundary layer (PBL) height is a key meteorological variable that affects the vertical transport of pollutants from the surface into the free troposphere, from where they can then undergo strong horizontal transport. Thus we have also investigated the impact of changing model resolution on PBL height and how this impacts O3 and NO2 concentrations. Spatial differences in PBL height between the two resolutions are shown in Sect. S2, Fig. S2 of the Supplement. In all seasons, over most of western and central Europe and especially in summer, the PBL height is generally lower when simulated at the coarse resolution (negative differences up to 275 m, Fig. S2c). In winter and spring (Fig. S2a and b), this lower height corresponds to generally higher O3 concentrations but also lower NO2 concentrations simulated at the coarse resolution, over the same region and vice versa in summer and autumn (Fig. S2c and d). If a deeper PBL is the main driver of pollutant trapping producing higher O3 levels, then we would also expect NO2 concentrations to be higher with a lower PBL height at the finer resolution, but their frequent inverse relationship suggest a stronger role for chemistry than PBL effects. However, these chemical and physical processes cannot be clearly separated.

Table 2Statistical results comparing seasonal mean PM2.5 concentrations simulated at the coarse and finer resolutions to observations from 25 stations within the EMEP network in 2007. Statistical results for all model grid-cells of both resolutions are also shown. Percentage differences between the two model resolutions are calculated as (PM2.5  coarse  resolution PM2.5  finer  resolution) (PM2.5  coarse  resolution).

Download Print Version | Download XLSX

In summary, we find a seasonal variation in simulated O3 differences between the two resolutions. Simulated O3 concentrations at the coarse resolution are higher in winter and spring and lower in summer and autumn compared to the finer resolution. We also find that in a number of locations, NO2 concentrations are lower at the coarse compared to the finer resolution and correspond to higher O3 concentrations at the coarse resolution as a result of reduced titration with lower NOx levels. Orography also plays an important role in some coastal locations, leading to an overestimation of O3 concentrations. The PBL height differs between the two resolutions especially during summer, with the finer resolution resulting in a deeper boundary layer. However, it is not possible to separate chemistry and mixing effects on simulated O3 concentrations.

3.3 The impact of model resolution on seasonal mean PM2.5: comparison with observations

Simulated seasonal mean PM2.5 concentrations are compared to available EMEP observations at 25 sites (Table 2). Mean values for the observations are fairly similar across all seasons, with values in summer and autumn being slightly lower. PM2.5 concentrations simulated at both the coarse and finer resolutions are lower in winter and higher in summer compared to measurements. In addition, mean PM2.5 concentrations simulated at the finer resolution are higher than those simulated at the coarse resolution except in summer. The coarse resolution simulates PM2.5 levels with the smallest bias during spring (NMB =0.2 %). In contrast, PM2.5 concentrations simulated at the finer resolution during spring have a large positive bias (NMB = 31 %). Similarly in autumn NMB values are larger for PM2.5 concentrations simulated at the finer resolution. We find that the largest bias for both resolutions occurs in summer with the coarse resolution resulting in a NMB of 70 %. Using, a similar finer configuration, Neal et al. (2017) found a year-round small positive bias in simulated PM2.5 concentrations averaged over a five year period (2001–2005) at two UK locations. The SD of PM2.5 concentrations across the 25 sites is fairly similar between model results and measurements except in winter, when simulated SD values are lower at both resolutions compared to measurements and in autumn, when the SD at the finer resolution is higher compared to measurements.

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f04

Figure 4Seasonal mean PM2.5 simulated at the finer resolution (a–d), and differences between seasonal mean PM2.5 at the coarse and finer resolution in 2007 (PM2.5  coarse  resolution PM2.5  finer  resolution) (e–h).

Download

Modelled versus measured PM2.5 concentrations across the 25 individual EMEP stations highlight the low simulated PM2.5 concentrations in winter (Sect. S2, Fig. S3 of the Supplement). Large variations in PM2.5 levels between the two resolutions are prominent in spring (31 %, Table 2). Smaller PM2.5 concentrations simulated at the coarse resolution in winter, spring and autumn are apparent (upward arrows, Fig. S3; negative differences, Table 2).

3.4 Impact of model resolution on seasonal mean PM2.5: spatial differences

Spatial distributions of PM2.5 concentrations, simulated at the finer resolution as well as differences between the two resolutions over the whole European domain are illustrated in Fig. 4. Over the whole domain, PM2.5 concentrations simulated at the finer resolution are lowest in winter (Fig. 4a) and highest in spring (Fig. 4b). As for O3, there is clear latitudinal gradient with higher PM2.5 levels in southern Europe in all seasons. Differences in seasonal mean PM2.5 concentrations, between the coarse and fine resolutions, vary seasonally across the European domain with the smallest differences occurring during winter (±3 µg m−3, Fig. 4e; 8 %, Table 2) in agreement with the findings for the 25 EMEP stations described above (Sect. 3.3). This suggests that at low PM2.5 concentrations ( 8 µg m−3) in winter, model results do not differ greatly when increasing the model resolution from 150 to 50 km. In spring, PM2.5 concentrations simulated at the coarse are lower than at the finer resolution over large parts of central and western Europe but are slightly higher in easternmost parts of Europe (negative differences 10 µg m−3, Fig. 4f; 6 %, Table 2), as found at the 25 EMEP station locations. The opposite result occurs in summer with generally higher PM2.5 concentrations simulated at the coarser resolution (positive differences  10 µg m−3, Fig. 4g;  29 %, Table 2). In autumn, the differences in PM2.5 concentrations at the two resolutions exhibit a marked east–west contrast, with lower values at the coarse resolution in western Europe (where the EMEP stations are generally located; Fig. 1) and higher values at the coarse resolution in eastern Europe (Fig. 4h). While PM2.5 concentrations at the 25 EMEP site locations are on average lower when simulated at the coarse resolution (23 %), over all grid-cells, PM2.5 concentrations are higher at the coarse resolution ( 8 %). This highlights issues with representativity of the EMEP network across Europe, with much fewer EMEP measurement stations for PM2.5 in eastern Europe.

The seasonality in PM2.5 differences, brought about by a change in model horizontal resolution, can be partly explained by differences in PBL height between the two resolutions, as outlined in Sect. 3.2. In particular, the deeper boundary layer in summer simulated at the finer resolution may lead to greater vertical lofting from the surface, producing lower PM2.5 levels compared to that simulated at the coarse resolution. In addition, differences in simulated precipitation (especially smaller-scale convective precipitation) between the two resolutions may be important, through its influence as the dominant mechanism in UKCA for removal of aerosols through wet deposition (O'Connor et al., 2014). Spatial patterns of convective precipitation differences between the two resolutions are shown in Sect. S2, Fig. S4 of the Supplement. In winter and spring, convective rainfall is higher at the coarse compared to the fine resolution (Fig. S4a and b). Thus removal of PM2.5 through wet deposition is greater, producing lower PM2.5 concentrations at the coarser resolution (Fig. 4e and f). The opposite holds in summer and autumn as the convective rainfall is lower at the coarse compared to the finer resolution (Fig. S4c and d) therefore resulting in higher PM2.5 concentrations simulated at the coarse resolution (Fig. 4g and h).

Overall, we also find a large seasonal variation in simulated PM2.5 concentrations between the two resolutions, with typically lower levels simulated in winter and spring at the coarse compared to the finer resolution and the opposite result in summer and autumn. Hence, the seasonality of differences in simulated PM2.5 concentrations between the two model resolutions is generally the inverse of that found for O3 in Sect. 3.3. We find that these seasonal differences can be largely explained by meteorological effects: PBL height differences, especially in summer, and differences in convective rainfall between the two resolutions.

Table 3Warm season (April–September) mean of daily maximum 8 h running mean O3 concentrations (MDA8 O3) and annual mean PM2.5 concentrations at the coarse and finer resolutions compared to observations from 52 and 25 stations within the EMEP network, respectively.

Download Print Version | Download XLSX

4 Sensitivity of health impact estimates to model resolution

We now examine how the differences in O3 and PM2.5 concentrations simulated at the two resolutions, influence health impact estimations across Europe at the country level. For this analysis we use warm season daily maximum 8 h running mean (MDA8) O3 (above 70 µg m−3) and annual-average PM2.5 concentrations. To estimate health impacts, air pollution concentrations (with an averaging period consistent with that used in epidemiological studies) are combined with population estimates and concentration–response coefficients (Sect. 2.3).

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f05

Figure 5Differences in (a) warm season (April–September) mean of daily maximum 8 h running mean O3 (concentrations above 70 µg m−3) and (b) annual mean PM2.5 between the coarse and finer resolution (coarse  finer).

Download

4.1 Warm season MDA8 O3 and annual-average PM2.5 concentrations

Statistics for warm season MDA8 O3 and annual PM2.5 concentrations compared between EMEP measurements and model results at the two resolutions are provided in Table 3. Mean simulated MDA8 O3 levels in the warm season at the 52 EMEP locations for both resolutions, are higher compared to observations (NMB = 11 and  9 %, Table 3), in agreement with our findings for summer and autumn mean O3 levels (c.f. Tables 1 and 3). The SD is also higher for both resolutions compared to observations. However, in contrast with summer mean O3 levels, mean simulated MDA8 O3 concentrations are 0.8 % higher at the coarse compared to the finer resolution at the 52 EMEP site locations (Table 3). Simulated annual mean PM2.5 concentrations are also higher compared to observations at the 25 locations (NMB = 10–20 %; Table 3) with concentrations being 8.7 % lower at the coarse compared to the finer resolution. This represents the net effect of seasonality in NMB shown in Table 2.

Differences in warm season MDA8 O3 and annual mean PM2.5 concentrations, simulated at the coarse and finer resolution, are shown in Fig. 5. The spatial distribution of differences in warm season MDA8 O3 between the two resolutions (Fig. 5a) is most similar to the distribution of differences in summer mean O3 concentrations (Fig. 3g). Differences in MDA8 O3 concentrations range from 7 µg m−3 in northeast Europe to +20 µg m−3 in southern Europe, the UK and Ireland (Fig. 5a). We note that if a different time-averaging period was chosen, for example, annual as opposed to warm season, the spatial patterns of MDA8 O3 differences would alter considerably due to the seasonal variation displayed in Fig. 3.

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f06

Figure 6(a) Differences between warm season mean daily maximum 8 h running mean (MDA8) O3 concentrations simulated at the two resolutions (coarse  finer) for population-weighted (PopW) concentrations (orange bars) and concentrations with no population-weighting (Not PopW) (blue bars) (b) The same as (a) but for annual mean PM2.5 concentrations. Countries are ordered by differences in PopW pollutant concentrations between the two resolutions.

Download

The spatial distribution of differences in annual mean PM2.5 concentrations between the two resolutions (Fig. 5b) are most similar to the spatial distribution of differences in spring and especially autumn mean PM2.5 concentrations – with a notable east–west gradient (Fig. 5). Differences in PM2.5 concentrations between the two resolutions range from 8 µg m−3 in the southwestern part of Europe and Cyprus to +4 µg m−3 in northern and eastern Europe (Fig. 5b).

4.2 Effect of applying population-weighting to MDA8 O3 and annual PM2.5 concentrations

The warm season MDA8 O3 concentrations and annual mean PM2.5 concentrations, simulated at both resolutions, were weighted by population totals for each country to produce country average population-weighted concentrations (Sect. 2.3). Figure 6a shows the impact of the two resolutions on country-average warm season average MDA8 O3 and the corresponding population-weighted MDA8 O3 concentrations. Similarly differences in annual mean PM2.5 concentrations between the two resolutions for non-population-weighted and population-weighted concentrations are shown in Fig. 6b.

Population-weighting of pollutant concentrations has different impacts across the European countries utilised in this study (Fig. 6a and b). In many countries, differences in population-weighted pollutant concentrations between the two resolutions are enhanced (i.e. larger positive or more negative differences) relative to non-population-weighted pollutant concentrations. However, in some countries population-weighting may reduce the positive or negative difference between the two resolutions. We examine several cases below.

For warm season MDA8 O3 concentrations, the largest negative differences, implying lower MDA8 O3 levels using the coarse compared to the finer resolution results, occur in eastern Europe (Fig. 5a). Hence, the largest negative differences in non-population-weighted and population-weighted MDA8 O3 concentrations are found in eastern European countries (Fig. 6a). The difference between the two resolutions is greatest when population-weighting is applied. This is generally due to slightly lower population-weighted MDA8 O3 concentrations compared to MDA8 O3 concentrations derived from the coarse resolution results (Sect. S3, Fig. S5a of the Supplement).

In the Netherlands warm season non-population-weighted MDA8 O3 is also lower when derived from coarse compared to finer resolution results (negative difference; Figs. 5a, 6a). However population-weighted MDA8 O3 concentrations are higher when derived from the coarse resolution results (Fig. 6a). This is caused by lower MDA8 O3 concentrations simulated at the finer resolution when applying population-weighting (Fig. S5a). This suggests that in populated regions, MDA8 O3 concentrations simulated at the finer resolution are lower which might be linked to higher NO2 concentrations.

Warm season MDA8 O3 show the largest positive differences, with higher values simulated at the coarse resolution, for southern Europe and the UK/Ireland (Fig. 5a). Thus, the largest positive differences for non-population-weighted and population-weighted MDA8 O3 concentrations occurs in southern European countries (Fig. 6a). Population–weighed MDA8 O3 concentrations in Portugal are higher compared to MDA8 O3 concentrations at the coarse but lower at the finer resolution (Fig. S5a). This suggests that, at the coarse resolution, areas with high levels of O3 are co-located with high population densities whilst at the finer resolution areas with lower levels of O3 are co-located with high population densities.

Annual-average PM2.5 concentrations show the largest negative differences, with higher values simulated at the finer resolution, in parts of western Europe (Fig. 5b). Hence, the largest negative non-population-weighted and population-weighted annual mean PM2.5 concentrations are found for Cyprus, Italy and Spain (Fig. 6b). Conversely, higher annual-average PM2.5 levels are simulated at the coarse resolution in eastern and northern Europe (Fig. 5b), hence larger positive non-population-weighted and population-weighted annual mean PM2.5 concentrations occur for countries in eastern and northern Europe (Fig. 6b).

In Cyprus, population-weighted annual mean PM2.5 concentrations simulated at the fine resolution are higher compared to concentrations with no population-weighting, due to denser populations being co-located with areas of higher PM2.5 levels (Fig. S5b). In Croatia, population-weighted annual mean PM2.5 concentrations simulated at the coarse resolution are greater than PM2.5 concentrations with no population-weighting, again due to denser populations in regions of high particulate matter concentration, but in this case when simulated at the coarse resolution (Fig. S5b). In a few countries (e.g. Switzerland), differences in population-weighted annual mean PM2.5 concentrations between the two resolutions have an opposite sign to differences between concentration with no population-weighting (Fig. 6b). This indicates that annual mean PM2.5 concentrations simulated at the finer resolution are high in densely populated regions but are low in these same regions at the coarse resolution.

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f07

Figure 7(a) AF associated with long-term exposure to daily maximum 8 h running mean O3 for each model resolution expressed as a percentage. (b) Differences in AF between the two resolutions expressed as a percentage for each European country (AFcoarse AFfiner). Grey lines show the 95 % CI which represents uncertainties associated only with the concentration–response coefficient used.

Download

It would be insightful to examine these population-weighted results in relation to model–observation biases in densely populated areas. However, as outlined in Sect. 2.2, the available sites in the EMEP database are urban background stations which are required to be representative of a wide area and away from industrial areas (EMEP/CCC, 2001). Nonetheless, we do note that in southern Europe, simulated summer mean MDA8 O3 concentrations at the finer resolution are closer to observations than concentrations simulated at the coarse resolution. We find no consistent result for model biases in simulated annual mean PM2.5 concentrations with respect to observations for the two model resolutions.

4.3 Attributable fraction of mortality associated with long-term exposure to O3

The attributable fraction (AF) associated with long-term exposure to MDA8 O3, expressed as a percentage of total respiratory mortality and simulated at both resolutions, was calculated for each country (Fig. 7a), using the population-weighted warm season MDA8 O3 concentrations (Fig. 6a) as discussed in Sect. 2.3. For both resolutions, the estimated AF is shown for each country, with the 95 % confidence interval (95 % CI) representing uncertainties associated only with the concentration–response coefficient (β) used (shown in grey). For all the countries considered, irrespective of the model resolution used, the AF of total respiratory mortality ranges from 1 % (95 % CI 0–2 %) in Finland to 11 % (95 % CI 4–18 %) in Cyprus (Fig. 7a).

Differences in AF between the countries are solely attributed to differences in population-weighted MDA8 O3 concentrations. Thus, countries with the highest population-weighted concentrations also have the highest AF. Similarly countries with the highest differences in population-weighted MDA8 O3 concentrations between the two resolutions also have the largest differences in AF between the coarse and finer resolution. If the AF was calculated for each model grid-cell rather than at the country level, the differences in AF for the two pollutants would have identical spatial distributions to the differences in warm season MDA8 O3 and annual-mean PM2.5 concentrations depicted in Fig. 5, as the AF is only dependent on the pollutant concentration and β (which is constant across all countries).

The differences in country level AF associated with long-term exposure to warm season MDA8 O3, simulated at the two resolutions, are shown in Fig. 7b. These values highlight the sensitivity of respiratory mortality attributable to long-term exposure to O3 to a change in model resolution. For most of northern and eastern Europe, the AF at the coarse resolution is lower than that at the finer resolution (negative differences, Fig. 7b) as for differences in population-weighted warm season MDA8 O3 concentrations in the same countries (Fig. 6a). In contrast, the AF at the coarse resolution is higher than that at the finer resolution for countries in southern Europe (positive differences, Fig. 7b). Differences in AF range from 0.9 % (95 % CI 0.3 to 1.5 %) in Poland to +2.6 % (95 % CI 1.0 to 4.1 %) in Portugal (Fig. 7b) which directly correspond to the countries having the lowest and highest difference in population-weighted MDA8 O3 concentration respectively (Fig. 6a; Note, although the differences in AF between the two resolution appear low, these are percentages of total respiratory mortality). In Poland and Portugal the estimated AF at the finer resolution is 1.4 times and 0.7 times that estimated at the coarse resolution, respectively. For approximately half of the European countries, the AF is higher for the coarse resolution compared to the finer resolution and vice versa. When considering the uncertainty associated with the concentration–response coefficient used, the sign of the difference of AF between the two model resolutions is unaltered (Fig. 7b). Over the majority of the countries, the AF attributable to long-term exposure to MDA8 O3 by the coarse resolution fall within the range of uncertainty as calculated by the finer resolution (Fig. 7a). However, over Finland and Ireland, the coarse mean estimates fall outside the uncertainty range estimates using the finer resolution (Fig. 7a).

For US averaged mortality estimates, Punger and West (2013) show that mortality estimates related to warm season long-term O3 exposure, calculated using the O3 concentrations at 36 km, were higher (by 12 %) than estimates calculated at the 12 km resolution. Resolution was also found to play and important role in determining health benefits associated with differences in O3 between 2005 and 2014 in the US (Thompson et al., 2014). In particular, in urban areas, Thompson et al. (2014) estimate that the benefits calculated using coarse resolution results were on average two times greater than estimates calculated using the finer scale results. As both of the above-mentioned studies are conducted in the US and use a different concentration response coefficient to that used in this paper, a definitive comparison between these studies and our estimates over Europe is not possible.

Since, seasonal differences in simulated O3 with resolution are considerable, the AF associated with long-term exposure to O3 was also calculated based on annual-mean (as opposed to summer-mean) O3 concentrations, which were in turn based on recommendations from Turner et al. (2015). Turner et al. (2015) suggest a higher concentration response coefficient of 1.06 (95 % CI: 1.04–1.08) per 10 µg m−3 and a slight lower MDA8 O3 threshold of 53.4 µg m−3 compared to values used in our study for summer-mean MDA8 O3. Using the values from Turner et al. (2015) the differences in AF are found to be of the same sign for the majority of the countries and the rankings across countries are largely similar. This similarity occurs because the difference in annual-mean MDA8 O3 concentrations between the two resolutions shows generally similar spatial patterns to the differences in warm season MDA8 O3 concentrations (not shown). However the ranges when using annual-mean O3 concentrations and recommendations from Turner et al. (2015) are larger: 2.3 to +12.0 %, compared to AF ranges given above for MDA8 O3. From further sensitivity analyses it is found that these greater AF ranges can be attributed to the use of a higher concentration-response coefficient (by a factor of approximately four) rather than differences in annual-mean compared to summer mean concentrations.

https://www.atmos-chem-phys.net/18/5765/2018/acp-18-5765-2018-f08

Figure 8(a) AF associated with long-term exposure to PM2.5 for each model resolution expressed as a percentage. (b) Differences in AF between the two resolutions expressed as a percentage for each European country (AFcoarse AFfiner). Grey lines show the 95 % CI which represents uncertainties associated only with the concentration–response coefficient used.

Download

4.4 Attributable Fraction associated with long-term exposure to PM2.5

The fraction of all-cause (excluding external) mortality attributable to long-term exposure to PM2.5, is shown as percentages for each country in Fig. 8a. The AF for all countries, irrespective of the resolution used, ranges from 2 % (95 % CI 1–3 %) in Iceland to 15 % (95 % CI 10–19 %) in Cyprus (Fig. 8a). Differences in AF between the two resolutions are shown in Fig. 8b. Since the variability in AF differences across the countries is caused by variability in population-weighted annual mean PM2.5 differences, Cyprus and countries in parts of western Europe have the largest negative difference in percentage AF (Fig. 8b). In contrast, countries in eastern and northern Europe have the largest positive difference in percentage AF (Fig. 8b). These differences range from -4.7 % (95 % CI 6.1 to 3.2 %) in Cyprus to 2.8 % (95 % CI 1.9 to 3.7 %) in Croatia. For Cyprus and Croatia, using the finer resolution results in an estimated AF that is 1.5 and 0.7 times that estimated using the coarse resolution, respectively. Over most countries, annual mean population-weighted PM2.5 concentrations are higher (positive difference, Fig. 6b) for the coarse compared to the finer resolution, thus resulting in a higher AF when using the coarse resolution results. Note, similar to O3, the uncertainty associated with the concentration–response coefficient for PM2.5 does not alter the sign of the difference of AF between the two model resolutions (Fig. 8b). For a number of countries, the mean AF attributable to long-term exposure to PM2.5 using the coarse resolution falls outside the uncertainty range of the finer estimates in particular over Iceland and Ireland (Fig. 8a).

We also examine the impact of using a low-concentration threshold. We apply a threshold of 5.8 µg m−3 (suggested by Burnett et al., 2014 which is derived from Lim et al., 2012) to annual mean PM2.5 concentrations. Differences in AF estimates associated with long-term exposure to population-weighted PM2.5 concentrations range from 4.8 to +2.1 % (as compared to 4.7 to +2.8 % above when no threshold is applied). The spatial distribution of these estimates remains unchanged and only slight changes in country rankings occur. Hence, the impact of applying a low concentrations threshold in this study for Europe is small.

Our results are consistent with other studies (but not all) that examine the impact of model resolution on health estimates associated with long-term exposure to PM2.5. Using concentrations simulated at the 36 km resolution, Punger and West (2013) find that the US national health estimate is higher (11 %) than the estimate at 12 km resolution. Li et al. (2015) also show that averaged over the US, a coarse grid resolution ( 200 km) results in a health estimate that is lower (8 %) than the estimated based on the fine scale model results ( 50 km), in contrast to our findings averaged across Europe. Thompson et al. (2014), in comparison, find that health benefits associated with changes in PM2.5 concentrations between 2005 and 2014 in the US, were not sensitive to resolution. Both Punger and West (2013) and Li et al. (2015) find that differences in PM2.5 are mainly attributable to primary anthropogenic PM, while Thompson et al. (2014) attribute the greatest differences (between 36 and 4 km resolutions) to secondary PM. However, in our study no substantial differences in PM2.5 components between the two resolutions were found. As previously stated, the above-mentioned studies are conducted in the US and hence definitive comparisons cannot be made with our results for Europe

In summary, our results suggest that differences in AF health estimates between coarse and finer resolutions vary across the different European countries. Our findings also indicate clear differences between southern and eastern Europe for exposure to warm season MDA8 O3, and west–east differences for exposure to annual-average PM2.5 due to the dependence of AF on populated weighted MDA8 O3 and annual PM2.5 concentrations. For differences in AF attributable to long-term exposure to summer mean MDA8 O3 and annual mean PM2.5 concentrations, the uncertainty associated with the concentration–response coefficient used does not alter the sign of the difference of AF between the two model resolutions (Figs. 7b and 8b). The uncertainty ranges for the PM2.5-related estimates show a greater variability between the two resolutions for more countries than the MDA8 O3-related AF estimates. Using the concentration–response coefficient in Jerrett et al. (2009), Thompson et al. (2014) find that the avoided mortalities due to difference in ozone concentrations between 2005 and 2014 at a 36 km model resolution are within the 95 % uncertainty range associated with the concentration–response coefficient used compared to estimates at a resolution of 12 and 4 km. These authors also find avoided mortalities associated with long-term effects of PM2.5 exposure at 36 km to fall within estimates at the 12 and 4 km resolution for three different concentration–response coefficients. Thus our results are in agreement for summer mean O3 but less so for annual mean PM2.5.

5 Conclusions

Chemistry–climate model simulations were performed at two resolutions: a coarse resolution ( 140 km) and a finer resolution ( 50 km). These simulations were carried out over Europe to quantify the impact of horizontal model resolution on simulated O3 and PM2.5 concentrations by season and on the associated Attributable Fraction (AF) of mortality due to long-term exposure to these two pollutants. Simulated O3 concentrations are lower in winter and higher in summer and autumn compared to measurements at both model resolutions. Results show a seasonal influence in the mean O3 differences between the two resolutions. Simulated O3 concentrations averaged across Europe at the coarse resolution are higher in winter and spring ( 10 and  6 %, respectively), and lower in summer and autumn (1 and 4 %, respectively) compared to the finer resolution. In contrast during winter and spring, NO2 concentrations are lower in some areas at the coarse compared to the finer configuration, whilst in summer and autumn, there are more locations where NO2 concentrations are higher at the coarse resolution. The lower O3 concentrations simulated at the finer compared to the coarse resolution can be partly explained by these higher NO2 levels that enhance titration of O3 at this finer resolution. The PBL height also differs between the two resolutions and may therefore account for differences in O3 concentrations; however, it is not possible to clearly separate the effects of chemistry and mixing on simulated O3.

Differences in PM2.5 concentrations simulated at the two resolutions also vary seasonally. Modelled PM2.5 concentrations are lower in winter and higher in summer compared to measurements at both resolutions. Simulated seasonal mean PM2.5 concentrations averaged across Europe during winter and spring are lower at the coarse compared to the finer resolution (8 and 6 %, respectively) but higher in summer and autumn ( 29 and  8 %, respectively). This seasonality in Europe-average differences in PM2.5 concentrations is the opposite to that found for differences in O3 concentrations between the two resolutions. Differences in PM2.5 concentrations simulated at the two resolutions are also influenced by PBL height, especially in summer when a deeper boundary layer at the finer resolution leads to greater lofting and lower PM2.5 concentrations. Furthermore, in all seasons, the differences in PM2.5 levels between the two resolutions are closely related to differences in the convective rainfall rate. In winter and spring, the convective rainfall at the coarse resolution is higher than that at the finer resolution thus resulting in lower PM2.5 concentrations. The opposite result holds in summer and autumn.

Results show that differences in warm season mean MDA8 O3 concentrations between the two resolutions are similar to summer mean differences in simulated O3 concentrations, with spatial patterns of differences revealing clear and important contrasts. Warm season MDA8 O3 levels are higher in most of southern Europe as well as the UK and Ireland, but lower in other areas of northern and eastern Europe when simulated at the coarse resolution compared to the finer resolution. In contrast, annual average PM2.5 concentrations are higher across most of northern and eastern Europe but lower over parts of southwest Europe at the coarse compared to the finer resolution.

Weighting the pollutant concentrations at both resolutions with the population within each country, results in some added differences between concentrations at the two resolutions, which also vary across the countries. In many countries, weighting by population enhances either positive or negative differences in warm season MDA8 O3 or annual mean PM2.5 concentrations between the two resolutions, which suggests that high levels of pollutant concentrations coincide with high population density at one resolution but low pollutant concentrations are co-located with high population density at the other resolution. Population-weighting pollutant concentrations also reduces differences between coarse and finer resolution results in some countries.

The AF of respiratory mortality associated with long-term exposure to warm season MDA8 O3 and annual mean PM2.5 is also sensitive to resolution as is it is solely driven by the simulated population-weighted pollutant concentrations. For the AF associated with long-term exposure to O3, countries in northern and eastern Europe have lower AF values at the coarse compared to the finer resolution whilst the opposite result occurs for other countries in southern Europe and Ireland. For the AF associated with long-term exposure to PM2.5, a few countries in southwestern Europe and Cyprus have lower AF values for PM2.5 concentrations simulated at the coarse resolution, whilst more countries especially in eastern and northern Europe show a higher AF when using PM2.5 concentrations simulated at the coarse resolution.

Overall, differences in the country-average AF associated with long-term exposure to MDA8 O3 range between 0.9 and +2.6 % while differences in the AF associated with long-term exposure to annual mean PM2.5 range from 4.7 to +2.8 % of the total baseline mortality. This result emphasises the importance of model horizontal resolution when conducting country specific health impact studies. We also find that the impacts of a 95 % CI in concentration–response coefficient is smaller than the impact of the model horizontal resolution. In addition, these ranges in AF associated with long-term exposure to annual mean PM2.5 were largely unaltered with the application of a low-concentration threshold for PM2.5.

Our calculation for O3 health impacts only considers warm-season MDA8 O3 impacts however these may differ to annual MDA8 O3 impacts because of seasonal differences in simulated O3 with resolution highlighted in this study. When using annual-mean MDA8 O3 concentrations alongside a recommended concentration–response coefficient and threshold suggested by Turner et al. (2015) the difference in AF between the two resolutions is considerably larger than our estimates using summer-mean MDA8 O3 concentrations. This is driven by the higher concentration–response coefficient (by a factor of approximately four) quoted in Turner et al. (2015) compared to that suggested by HRAPIE for summer mean MDA8 O3 concentrations (WHO, 2013). In addition, for our study we apply the same concentration–response coefficient to all populations and assumed that for PM2.5-related health impacts, all PM2.5 components have the same impact on mortality.

The pollutant concentrations used in this study have been extracted at the lowest model level with a mid-point at 20 m. The sensitivity of our simulated pollutant concentrations to vertical model resolution has not been examined. Future research focusing on the sensitivity of AF changes to different averaging periods or seasons would be beneficial. In addition, the use of concentration–response coefficients that are derived from European cohort data would be useful, although such data are limited. Nonetheless this study provides one of the first insights as to how air pollution related health impacts over Europe are influenced by the model resolution used to simulate pollutant concentrations.

Data availability

The following data has been used for this study: UKCA chemistry-climate model results courtesy of UK Met Office facilities, EMEP measurement data (http://ebas.nilu.no; UNECE, 2009; Tørseth et al., 2012), gridded population data (SEDAC; CIESIN, 2005).

Supplement

The supplement related to this article is available online at: https://doi.org/10.5194/acp-18-5765-2018-supplement.

Competing interests

The authors declare that they have no conflict of interest.

Acknowledgements

Sara Fenech's PhD was funded by Public Health England. The development of the United Kingdom Chemistry and Aerosol (UKCA) model and Fiona M. O'Connor are supported by the Joint UK BEIS/Defra Met Office Hadley Centre Climate Programme (GA01101).

Edited by: Bryan N. Duncan
Reviewed by: two anonymous referees

References

Anenberg, S. C., West, J. J., Fiore, A. M., Jaffe, D. A., Prather, M., Bergmann, D., Cuvelier, K., and Dentener, F. J.: Intercontinental Impacts of Ozone Pollution on Human Mortality, Environ. Sci. Technol., 43, 6482–6487, https://doi.org/10.1021/es900518z, 2009. 

Anenberg, S. C., Horowitz, L. W., Tong, D. Q., and West, J. J.: An estimate of the global burden of anthropogenic ozone and fine particulate matter on premature human mortality using atmospheric modeling, Environ. Health Perspect., 118, 1189–1195, https://doi.org/10.1289/ehp.0901220, 2010. 

Arunachalam, S., Wang, B., Davis, N., Baek, B. H., and Levy, J. I.: Effect of chemistry-transport model scale and resolution on population exposure to PM2.5 from aircraft emissions during landing and takeoff, Atmos. Environ., 45, 3294–3300, https://doi.org/10.1016/j.atmosenv.2011.03.029, 2011. 

Bellouin, N., Rae, J., Jones, A., Johnson, C., Haywood, J., and Boucher, O.: Aerosol forcing in the Climate Model Intercomparison Project (CMIP5) simulations by HadGEM2-ES and the role of ammonium nitrate, J. Geophys. Res.-Atmos., 116, 1–25, https://doi.org/10.1029/2011JD016074, 2011. 

Brook, R. D., Rajagopalan, S., Pope, C. A., Brook, J. R., Bhatnagar, A., Diez-Roux, A. V., Holguin, F., Hong, Y., Luepker, R. V., Mittleman, M. A., Peters, A., Siscovick, D., Smith, S. C., Whitsel, L., and Kaufman, J. D.: Particulate matter air pollution and cardiovascular disease: An update to the scientific statement from the american heart association, Circulation, 121, 2331–2378, https://doi.org/10.1161/CIR.0b013e3181dbece1, 2010. 

Brown, A., Milton, S., Cullen, M., Golding, B., Mitchell, J., and Shelly, A.: Unified modeling and prediction of weather and climate: A 25-year journey, B. Am. Meteorol. Soc., 93, 1865–1877, https://doi.org/10.1175/BAMS-D-12-00018.1, 2012. 

Burnett, R. T., Arden Pope, C., Ezzati, M., Olives, C., Lim, S. S., Mehta, S., Shin, H. H., Singh, G., Hubbell, B., Brauer, M., Ross Anderson, H., Smith, K. R., Balmes, J. R., Bruce, N. G., Kan, H., Laden, F., Prüss-Ustün, A., Turner, M. C., Gapstur, S. M., Diver, W. R., and Cohen, A.: An integrated risk function for estimating the global burden of disease attributable to ambient fine particulate matter exposure, Environ. Health Perspect., 122, 397–403, https://doi.org/10.1289/ehp.1307049, 2014. 

Center for International Earth Science Information Network (CIESIN): Gridded Population of the World, Version 3 (GPWv3): Population Count Grid, Future Estimates. Columbia University, United Nations Food and Agriculture Programme (FAO), and Centro Internacional de Agricultura Tropical (CIAT), NASA Socioeconomic Data and Applications Center (SEDAC), Palisades, NY, USA, https://doi.org/10.7927/H42B8VZZ (last access: 23 April 2018), 2005. 

Cohen, A. J., Anderson, H. R., Ostro, B., Pandey, K. D., Krzyzanowski, M., Künzli, N., Gutschmidt, K., Iii, C. A. P., Romieu, I., Samet, J. M., and Smith, K. R.: Urban Air Pollution, in Urban air pollution., in: Comparative quantification of health risks: global and regional burden of disease due to selected major risk factors, edited by: Ezzati, M., Lopez, A., Rodgers, A., and Murray, C., 1353–1434, World Health Organization, Geneva, Switzerland, 2004. 

Cohen, A. J., Brauer, M., Burnett, R., Anderson, H. R., Frostad, J., Estep, K., Balakrishnan, K., Brunekreef, B., Dandona, L., Dandona, R., Feigin, V., Freedman, G., Hubbell, B., Jobling, A., Kan, H., Knibbs, L., Liu, Y., Martin, R., Morawska, L., Pope, C. A., Shin, H., Straif, K., Shaddick, G., Thomas, M., van Dingenen, R., van Donkelaar, A., Vos, T., Murray, C. J. L., and Forouzanfar, M. H.: Estimates and 25-year trends of the global burden of disease attributable to ambient air pollution: an analysis of data from the Global Burden of Diseases Study 2015, Lancet, 389, 1907–1918, https://doi.org/10.1016/S0140-6736(17)30505-6, 2017. 

Coleman, L., Varghese, S., Tripathi, O. P., Jennings, S. G., and O'Dowd, C. D.: Regional-Scale Ozone Deposition to North-East Atlantic Waters, Adv. Meteorol., 2010, 1–16, https://doi.org/10.1155/2010/243701, 2010. 

Colette, A., Bessagnet, B., Vautard, R., Szopa, S., Rao, S., Schucht, S., Klimont, Z., Menut, L., Clain, G., Meleux, F., Curci, G., and Rouïl, L.: European atmosphere in 2050, a regional air quality and climate perspective under CMIP5 scenarios, Atmos. Chem. Phys., 13, 7451–7471, https://doi.org/10.5194/acp-13-7451-2013, 2013. 

Collins, W. J., Bellouin, N., Doutriaux-Boucher, M., Gedney, N., Halloran, P., Hinton, T., Hughes, J., Jones, C. D., Joshi, M., Liddicoat, S., Martin, G., O'Connor, F., Rae, J., Senior, C., Sitch, S., Totterdell, I., Wiltshire, A., and Woodward, S.: Development and evaluation of an Earth–System model – HadGEM2, Geosci. Model Dev., 4, 1051–1075, https://doi.org/10.5194/gmd-4-1051-2011, 2011. 

COMEAP: Quantification of Mortality and Hospital Admissions Associated with Ground-level Ozone, produced by Public Health England for the Committee on the Medical Effects of Air Pollutants, UK, available at: https://assets.publishing.service.gov.uk/government/uploads/system/uploads/attachment_data/file/492949/COMEAP_Ozone_Report_2015__rev1_.pdf (last access: 24 April 2018), 2015. 

EMEP/CCC: EMEP Manual for Sampling and Analysis, Norwegion Inst. Air Res., available at: https://www.nilu.no/projects/ccc/manual/index.html (last access: 14 March 2018), 2001. 

Fang, Y., Naik, V., Horowitz, L. W., and Mauzerall, D. L.: Air pollution and associated human mortality: the role of air pollutant emissions, climate change and methane concentration increases from the preindustrial period to present, Atmos. Chem. Phys., 13, 1377–1394, https://doi.org/10.5194/acp-13-1377-2013, 2013. 

Fiore, A. M., Dentener, F. J., Wild, O., Cuvelier, C., Schultz, M. G., Hess, P., Textor, C., Schulz, M., Doherty, R. M., Horowitz, L. W., MacKenzie, I. A., Sanderson, M. G., Shindell, D. T., Stevenson, D. S., Szopa, S., Van Dingenen, R., Zeng, G., Atherton, C., Bergmann, D., Bey, I., Carmichael, G., Collins, W. J., Duncan, B. N., Faluvegi, G., Folberth, G., Gauss, M., Gong, S., Hauglustaine, D., Holloway, T., Isaksen, I. S. A., Jacob, D. J., Jonson, J. E., Kaminski, J. W., Keating, T. J., Lupu, A., Manner, E., Montanaro, V., Park, R. J., Pitari, G., Pringle, K. J., Pyle, J. A., Schroeder, S., Vivanco, M. G., Wind, P., Wojcik, G., Wu, S., and Zuber, A.: Multimodel estimates of intercontinental source-receptor relationships for ozone pollution, J. Geophys. Res.-Atmos., 114, 1–21, https://doi.org/10.1029/2008JD010816, 2009. 

Folberth, G. A., Abraham, N. L., Johnson, C. E., Morgenstern, O., O'Connor, F. M., Pacifico, F., Young, P. A., Collins, W. J., and Pyle, J. A.: Evaluation of the new UKCA climate-composition model. Part III. Extension to Tropospheric Chemistry and Biogeochemical Coupling between Atmosphere and Biosphere, in preparation, 2018. 

Forouzanfar, M. H., Afshin, A., Alexander, L. T., et al.: Global, regional, and national comparative risk assessment of 79 behavioural, environmental and occupational, and metabolic risks or clusters of risks, 1990–2015: a systematic analysis for the Global Burden of Disease Study 2015, Lancet, 388, 1659–1724, https://doi.org/10.1016/S0140-6736(16)31679-8, 2016. 

Gowers, A. M., Miller, B. G., and Stedman, J. R.: Estimating Local Mortality Burdens associated with Particulate Air Pollution, available at: http://www.hpa.org.uk/webc/HPAwebFile/HPAweb_C/1317141074607 (last access: 19 April 2018), 2014. 

Gryparis, A., Forsberg, B., Katsouyanni, K., Analitis, A., Touloumi, G., Schwartz, J., Samoli, E., Medina, S., Anderson, H. R., Niciu, E. M., Wichmann, H. E., Kriz, B., Kosnik, M., Skorkovsky, J., Vonk, J. M., and Dörtbudak, Z.: Acute effects of ozone on mortality from the “Air Pollution and Health: A European Approach” project, Am. J. Resp. Crit. Care, 170, 1080–1087, https://doi.org/10.1164/rccm.200403-333OC, 2004. 

Guenther, A., Hewitt, C. N., Erickson, D., Fall, R., Geron, C., Graedel, T., Harley, P., Klinger, L., Lerdau, M., McKay, W. A., Pierce, T., Scholes, B., Steinbrecher, R., Tallamraju, R., Taylor, J., and Zimmerman, P.: A global model of natural volatile organic compound emissions, J. Geophys. Res., 100, 8873, https://doi.org/10.1029/94JD02950, 1995. 

Hoek, G., Krishnan, R. M., Beelen, R., Peters, A., Ostro, B., Brunekreef, B., and Kaufman, J. D.: Long-term air pollution exposure and cardio- respiratory mortality: a review, Environ. Health, 12, 43, https://doi.org/10.1186/1476-069X-12-43, 2013. 

Jerrett, M., Burnett, R. T., Pope, C. A., Ito, K., Thurston, G., Krewski, D., Shi, Y., Calle, E., and Thun, M.: Long-Term Ozone Exposure and Mortality, New Engl. J. Med., 360, 1085–1095, https://doi.org/10.1056/NEJMoa0803894, 2009. 

Jones, A., Roberts, D. L., Woodage, M. J., and Johnson, C. E.: Indirect sulphate aerosol forcing in a climate model with an interactive sulphur cycle, J. Geophys. Res., 106, 20293–20310, 2001. 

Krewski, D.: Extended Follow-Up and Spatial Analysis of the American Cancer Society Study Linking Particulate Air Pollution and Mortality, Health Effects Institute Research Report 140, Boston, USA, 2009. 

Lamarque, J.-F., Bond, T. C., Eyring, V., Granier, C., Heil, A., Klimont, Z., Lee, D., Liousse, C., Mieville, A., Owen, B., Schultz, M. G., Shindell, D., Smith, S. J., Stehfest, E., Van Aardenne, J., Cooper, O. R., Kainuma, M., Mahowald, N., McConnell, J. R., Naik, V., Riahi, K., and van Vuuren, D. P.: Historical (1850–2000) gridded anthropogenic and biomass burning emissions of reactive gases and aerosols: methodology and application, Atmos. Chem. Phys., 10, 7017–7039, https://doi.org/10.5194/acp-10-7017-2010, 2010. 

Lelieveld, J., Evans, J. S., Fnais, M., Giannadaki, D., and Pozzer, A.: The contribution of outdoor air pollution sources to premature mortality on a global scale, Nature, 525, 367–371, https://doi.org/10.1038/nature15371, 2015. 

Li, Y., Henze, D. K., Jack, D., and Kinney, P. L.: The influence of air quality model resolution on health impact assessment for fine particulate matter and its components, Air Qual. Atmos. Hlth., 9, 51–68, https://doi.org/10.1007/s11869-015-0321-z, 2015. 

Lim, S. S., Vos, T., Flaxman, A. D., et al.: A comparative risk assessment of burden of disease and injury attributable to 67 risk factors and risk factor clusters in 21 regions, 1990–2010: A systematic analysis for the Global Burden of Disease Study 2010, Lancet, 380, 2224–2260, https://doi.org/10.1016/S0140-6736(12)61766-8, 2012. 

Lock, A. P., Brown, A. R., Bush, M. R., Martin, G. M., and Smith, R. N. B.: A New Boundary Layer Mixing Scheme. Part I: Scheme Description and Single-Column Model Tests, Mon. Weather Rev., 128, 3187–3199, https://doi.org/10.1175/1520-0493(2000)128<3187:ANBLMS>2.0.CO;2, 2000. 

Malley, C. S., Henze, D. K., Kuylenstierna, J. C. I., Vallack, H. W., Davila, Y., Anenberg, S. C., Turner, M. C., and Ashmore, M. R.: Updated global estimates of respiratory mortality in adults = 30 years of age attributable to long-term ozone exposure, Environ. Health Perspect., 125, 1–9, https://doi.org/10.1289/EHP1390, 2017. 

Markakis, K., Valari, M., Perrussel, O., Sanchez, O., and Honore, C.: Climate-forced air-quality modeling at the urban scale: sensitivity to model resolution, emissions and meteorology, Atmos. Chem. Phys., 15, 7703–7723, https://doi.org/10.5194/acp-15-7703-2015, 2015. 

Morgenstern, O., Braesicke, P., O'Connor, F. M., Bushell, A. C., Johnson, C. E., Osprey, S. M., and Pyle, J. A.: Evaluation of the new UKCA climate-composition model – Part 1: The stratosphere, Geosci. Model Dev., 2, 43–57, https://doi.org/10.5194/gmd-2-43-2009, 2009. 

Moufouma-Okia, W. and Jones, R.: Resolution dependence in simulating the African hydroclimate with the HadGEM3-RA regional climate model, Clim. Dynam., 44, 609–632, https://doi.org/10.1007/s00382-014-2322-2, 2014. 

Neal, L. S., Dalvi, M., Folberth, G., McInnes, R. N., Agnew, P., O'Connor, F. M., Savage, N. H., and Tilbee, M.: A description and evaluation of an air quality model nested within global and regional composition-climate models using MetUM, Geosci. Model Dev., 10, 3941–3962, https://doi.org/10.5194/gmd-10-3941-2017, 2017. 

O'Connor, F. M., Johnson, C. E., Morgenstern, O., Abraham, N. L., Braesicke, P., Dalvi, M., Folberth, G. A., Sanderson, M. G., Telford, P. J., Voulgarakis, A., Young, P. J., Zeng, G., Collins, W. J., and Pyle, J. A.: Evaluation of the new UKCA climate-composition model – Part 2: The Troposphere, Geosci. Model Dev., 7, 41–91, https://doi.org/10.5194/gmd-7-41-2014, 2014. 

Pacifico, F., Harrison, S. P., Jones, C. D., Arneth, A., Sitch, S., Weedon, G. P., Barkley, M. P., Palmer, P. I., Serça, D., Potosnak, M., Fu, T.-M., Goldstein, A., Bai, J., and Schurgers, G.: Evaluation of a photosynthesis-based biogenic isoprene emission scheme in JULES and simulation of isoprene emissions under present-day climate conditions, Atmos. Chem. Phys., 11, 4371–4389, https://doi.org/10.5194/acp-11-4371-2011, 2011. 

Punger, E. M. and West, J. J.: The effect of grid resolution on estimates of the burden of ozone and fine particulate matter on premature mortality in the United States., Air Qual. Atmos. Hlth., 6, 563–573, https://doi.org/10.1007/s11869-013-0197-8, 2013. 

Schaap, M., Cuvelier, C., Hendriks, C., Bessagnet, B., Baldasano, J. M., Colette, A., Thunis, P., Karam, D., Fagerli, H., Graff, A., Kranenburg, R., Nyiri, A., Pay, M. T., Rouïl, L., Schulz, M., Simpson, D., Stern, R., Terrenoire, E., and Wind, P.: Performance of European chemistry transport models as function of horizontal resolution, Atmos. Environ., 112, 90–105, https://doi.org/10.1016/j.atmosenv.2015.04.003, 2015. 

Silva, R. A., West, J. J., Zhang, Y., Anenberg, S. C., Lamarque, J.-F., Shindell, D. T., Collins, W. J., Dalsoren, S., Faluvegi, G., Folberth, G., Horowitz, L. W., Nagashima, T., Naik, V., Rumbold, S., Skeie, R., Sudo, K., Takemura, T., Bergmann, D., Cameron-Smith, P., Cionni, I., Doherty, R. M., Eyring, V., Josse, B., MacKenzie, I. A., Plummer, D., Righi, M., Stevenson, D. S., Strode, S., Szopa, S., and Zeng, G.: Global premature mortality due to anthropogenic outdoor air pollution and the contribution of past climate change, Environ. Res. Lett., 8, 1748–9326, https://doi.org/10.1088/1748-9326/8/3/034005, 2013. 

Stock, Z. S., Russo, M. R., and Pyle, J. A.: Representing ozone extremes in European megacities: the importance of resolution in a global chemistry climate model, Atmos. Chem. Phys., 14, 3899–3912, https://doi.org/10.5194/acp-14-3899-2014, 2014. 

Thompson, T. M. and Selin, N. E.: Influence of air quality model resolution on uncertainty associated with health impacts, Atmos. Chem. Phys., 12, 9753–9762, https://doi.org/10.5194/acp-12-9753-2012, 2012. 

Thompson, T. M., Saari, R. K., and Selin, N. E.: Air quality resolution for health impact assessment: influence of regional characteristics, Atmos. Chem. Phys., 14, 969–978, https://doi.org/10.5194/acp-14-969-2014, 2014. 

Tie, X., Brasseur, G., and Ying, Z.: Impact of model resolution on chemical ozone formation in Mexico City: application of the WRF-Chem model, Atmos. Chem. Phys., 10, 8983–8995, https://doi.org/10.5194/acp-10-8983-2010, 2010. 

Tørseth, K., Aas, W., Breivik, K., Fjæraa, A. M., Fiebig, M., Hjellbrekke, A. G., Lund Myhre, C., Solberg, S., and Yttri, K. E.: Introduction to the European Monitoring and Evaluation Programme (EMEP) and observed atmospheric composition change during 1972–2009, Atmos. Chem. Phys., 12, 5447–5481, https://doi.org/10.5194/acp-12-5447-2012, 2012. 

Turner, M. C., Jerrett, M., Pope, C. A., Krewski, D., Gapstur, S. M., Diver, W. R., Beckerman, B. S., Marshall, J. D., Su, J., Crouse, D. L., and Burnett, R. T.: Long-Term Ozone Exposure and Mortality in a Large Prospective Study, Am. J. Resp. Crit. Care, 193, 1134–1142, https://doi.org/10.1164/rccm.201508-1633OC, 2015. 

United Nations Economic Commissions for Europe (UNECE): EMEP monitoring strategy for 2010–2019, Geneva, Switzerland, ECE/EB.AIR/2009/16/Rev1, available at: https://www.unece.org/fileadmin/DAM/env/documents/2013/air/emep/Informal_document_no_20_Revised_Strategy_for_EMEP_for_2010-2019_clean_text.pdf (last access: 23 April 2018), 2009. 

Valari, M. and Menut, L.: Does an Increase in Air Quality Models' Resolution Bring Surface Ozone Concentrations Closer to Reality?, J. Atmos. Ocean. Tech., 25, 1955–1968, https://doi.org/10.1175/2008JTECHA1123.1, 2008. 

Walters, D. N., Best, M. J., Bushell, A. C., Copsey, D., Edwards, J. M., Falloon, P. D., Harris, C. M., Lock, A. P., Manners, J. C., Morcrette, C. J., Roberts, M. J., Stratton, R. A., Webster, S., Wilkinson, J. M., Willett, M. R., Boutle, I. A., Earnshaw, P. D., Hill, P. G., MacLachlan, C., Martin, G. M., Moufouma-Okia, W., Palmer, M. D., Petch, J. C., Rooney, G. G., Scaife, A. A., and Williams, K. D.: The Met Office Unified Model Global Atmosphere 3.0/3.1 and JULES Global Land 3.0/3.1 configurations, Geosci. Model Dev., 4, 919–941, https://doi.org/10.5194/gmd-4-919-2011, 2011. 

West, J. J., Naik, V., Horowitz, L. W., and Fiore, A. M.: Effect of regional precursor emission controls on long-range ozone transport – Part 2: Steady-state changes in ozone air quality and impacts on human mortality, Atmos. Chem. Phys., 9, 6095–6107, https://doi.org/10.5194/acp-9-6095-2009, 2009. 

WHO: Health Risks of Air Pollution in Europe – HRAPIE project: Recommendations for concentration-response functions for cost-benefit analysis of particulate matter, ozone and nitrogen dioxide, available at: http://www.euro.who.int/__data/assets/pdf_file/0006/238956/Health_risks_air_pollution_HRAPIE_project.pdf?ua=1 (last access: 19 April 2018), 2013.  

Yu, K., Jacob, D. J., Fisher, J. A., Kim, P. S., Marais, E. A., Miller, C. C., Travis, K. R., Zhu, L., Yantosca, R. M., Sulprizio, M. P., Cohen, R. C., Dibb, J. E., Fried, A., Mikoviny, T., Ryerson, T. B., Wennberg, P. O., and Wisthaler, A.: Sensitivity to grid resolution in the ability of a chemical transport model to simulate observed oxidant chemistry under high-isoprene conditions, Atmos. Chem. Phys., 16, 4369–4378, https://doi.org/10.5194/acp-16-4369-2016, 2016. 

Download
Short summary
The impact of model horizontal resolution on simulated surface ozone and particulate matter less than 2.5 μm concentrations, and the associated health impacts over Europe, using a coarse (~ 140 km) and a finer (~ 50 km) resolution is examined. Results highlight a strong seasonal variation in simulated O3 and PM2.5 differences between the two resolutions and demonstrate that health impact assessments are sensitive to a change in model resolution by up to ±5 % of the total mortality across Europe.
Altmetrics
Final-revised paper
Preprint