Atmos. Chem. Phys., 13, 1895-1912, 2013
www.atmos-chem-phys.net/13/1895/2013/
doi:10.5194/acp-13-1895-2013
© Author(s) 2013. This work is distributed
under the Creative Commons Attribution 3.0 License.
Modeling of 2008 Kasatochi volcanic sulfate direct radiative forcing: assimilation of OMI SO2 plume height data and comparison with MODIS and CALIOP observations
J. Wang1, S. Park1, J. Zeng1, C. Ge1,6, K. Yang2,4, S. Carn3, N. Krotkov4, and A. H. Omar5
1Department of Earth and Atmospheric Sciences, University of Nebraska, Lincoln, NE, USA
2Department of Atmospheric and Oceanic Science, University of Maryland, College Park, MD, USA
3Department of Geological and Mining Engineering and Sciences, Michigan Technological University, Houghton, MI, USA
4Atmospheric Chemistry and Dynamics Laboratory, NASA Goddard Space Flight Center, Greenbelt, MD, USA
5Science Directorate, NASA Langley Research Center, Hampton, VA, USA
6State Key Laboratory of Atmospheric Boundary Layer Physics and Atmospheric Chemistry, Institute of Atmospheric Physics, Chinese Academy of Sciences, Beijing, China

Abstract. Volcanic SO2 column amount and injection height retrieved from the Ozone Monitoring Instrument (OMI) with the Extended Iterative Spectral Fitting (EISF) technique are used to initialize a global chemistry transport model (GEOS-Chem) to simulate the atmospheric transport and lifecycle of volcanic SO2 and sulfate aerosol from the 2008 Kasatochi eruption, and to subsequently estimate the direct shortwave, top-of-the-atmosphere radiative forcing of the volcanic sulfate aerosol. Analysis shows that the integrated use of OMI SO2 plume height in GEOS-Chem yields: (a) good agreement of the temporal evolution of 3-D volcanic sulfate distributions between model simulations and satellite observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) and Cloud-Aerosol Lidar with Orthogonal Polarisation (CALIOP), and (b) an e-folding time for volcanic SO2 that is consistent with OMI measurements, reflecting SO2 oxidation in the upper troposphere and stratosphere is reliably represented in the model. However, a consistent (~25%) low bias is found in the GEOS-Chem simulated SO2 burden, and is likely due to a high (~20%) bias of cloud liquid water amount (as compared to the MODIS cloud product) and the resultant stronger SO2 oxidation in the GEOS meteorological data during the first week after eruption when part of SO2 underwent aqueous-phase oxidation in clouds. Radiative transfer calculations show that the forcing by Kasatochi volcanic sulfate aerosol becomes negligible 6 months after the eruption, but its global average over the first month is −1.3 Wm−2, with the majority of the forcing-influenced region located north of 20° N, and with daily peak values up to −2 Wm−2 on days 16–17. Sensitivity experiments show that every 2 km decrease of SO2 injection height in the GEOS-Chem simulations will result in a ~25 % decrease in volcanic sulfate forcing; similar sensitivity but opposite sign also holds for a 0.03 μm increase of geometric radius of the volcanic aerosol particles. Both sensitivities highlight the need to characterize the SO2 plume height and aerosol particle size from space. While more research efforts are warranted, this study is among the first to assimilate both satellite-based SO2 plume height and amount into a chemical transport model for an improved simulation of volcanic SO2 and sulfate transport.

Citation: Wang, J., Park, S., Zeng, J., Ge, C., Yang, K., Carn, S., Krotkov, N., and Omar, A. H.: Modeling of 2008 Kasatochi volcanic sulfate direct radiative forcing: assimilation of OMI SO2 plume height data and comparison with MODIS and CALIOP observations, Atmos. Chem. Phys., 13, 1895-1912, doi:10.5194/acp-13-1895-2013, 2013.
 
Search ACP
Final Revised Paper
PDF XML
Citation
Discussion Paper
Share